PENGARUH VARIASI KUAT ARUS LAS LISTRIK PADA PENGELASAN BAJA C45 DENGAN SUDUT KAMPU V GANDA TERHADAP UJI TARIK DAN UJI IMPAK
Keywords:
Cutting force, Carbide tool, characteristics, Maximum temperature
Abstract
The research of Carbide Cut Chisel concludes that every time there is a change in the execution of the work, indirectly changes in cutting speed, heat energy in metal cutting, heat due to chip chisel friction, heat arising from the scissors force. although done with a fixed force from this result data is obtained for processing time 2, 4 and 8 hours cutting speed (Vc) = 2.66 m / s, 3.16 m / s, 3.83 m / s with cutting power ( Pc) = 14.77 Hp and Electro Motor Power (Pg) = 18.7 Hp. For forces that occur in the turning process obtained Fc = 350 kg, Ft = 180.3 kg, Fs = 280.9 kg, Fns = 350 kg, Fv = 397 kg, Ff = 218 kg, Fn = 332 kg. The results obtained for Pm are 102 kal / s, 169kal / s for Pf is 2172 kal / s, 2580 kal / s, 3127 kal / s for Ps is 128 kal / s, 152 kal / s 184 cal / s. Temperature Zone 1 and Temperature Zone 2 are for Өm are 76.940C, 76.93 0C, 73.28 0C and Өf are 4.82 0 C with a time of 2.4 and 8 hours. Next for mtm = 584 0C, 583 0 C, 582 0C. For ∆ts are: 8.6 0C, 8.5 0C, 8.4 0C. For ∆to = Room temperature is taken 28 0C. For Maximun Temperature ∆. max = 620.6 0C, 619.50C, 618.4 0C.
Downloads
Download data is not yet available.
References
[1] D. D. S. 2 Ivan Norma Susila 1, Zainal Arifin 2, “PENGARUH SUDUT POTONG PAHAT TERHADAP GAYA PEMOTONGAN PADA PROSES BUBUT BEBERAPA MATERIAL DENGAN PAHAT HSS,” MEKANIKA, vol. 12, no. 1, pp. 28–33, 2013.
[2] S. Hestukoro, T. Siagian, A. Bakhori, and I. Siregar, “Analysis Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[3] S. Hestukoro, T. Siagian, A. Bukhori, I. Roza, and I. Siregar, “Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[4] M. akhi. junaidi, m.idris, “Analisa Pahat Potong HSS Dengan Material Besi Cor Pada Mesin Bubut Universal,” MEDAN, 1, 2015.
[5] Junaidi, “WORKING PROCESS OF TU 3A CNC FRAIS MACHINE USING SOFTWARE SYSTEM.”
[6] A. Yanie, “ANALYSIS CUTTING TOOL HIGH SPEED STEEL (HSS ) WITH CAST IRON MATERIAL FROM UNIVERSAL LATHE.”
[7] J. Junaidi, METROLOGI DAN PENGUKURAN, 1st ed. MEDAN: P4M UNHAR, 2018.
[8] JUNAIDI, ANALISA PERHITUNGAN PAHAT POTONG, 1st ed. MEDAN: Sekolah TinggiTeknik Harapan (STTH) Medan, 2016.
[9] I. M. L. Batan, “Metode Pemeriksaan Mampu Ukur Suatu Rancangan Ditinjau dari Spesifikasi Produk Dengan Bantuan Checklist,” J. Tek. Mesin, Vol. 2, Nomor 1, Januari 2002, vol. 2, no. 1, pp. 1–8, 2002.
[10] Jusuf Talaperu*), “PEMOTONGAN LOGAM/ DETAIL PRODUK SECARA EKONOMIS PADA MESIN BUBUT PRODUKSI KONVENSIONAL,” TEKNOLOGI, vol. 8, no. 2, pp. 917–920, 2011.
[11] B. S. Angga Zeptiawan Sastal1, Yuspian Gunawan2, “PENGARUH KECEPATAN POTONG TERHADAP PERUBAHAN TEMPERATUR PAHAT DAN KEAUSAN PAHAT BUBUT PADA PROSES PEMBUBUTAN BAJA KARBON SEDANG,” ENTHALPY-Jurnal Ilm. Mhs. Tek. Mesin, vol. 3, no. 1, pp. 1–11.
[12] (4) Hernadewita (1) Hendra, (2) Sutarmadi, (3) Anizar Indriani, “JENIS MATERIAL PAHAT POTONG DAN RUN OUT TERHADAP KEKASARAN PERMUKAAN BENDA KERJA SILINDER PADA PROSES BUBUT,” Jenis Mater. Pahat Potong Dan Run Out Terhadap Kekasaran Permukaan Benda Kerja Silinder Pada Proses Bubut, vol. 4, no. 2, pp. 376–385.
[13] M. I. P. H. dan W. J. Mustafid Amna Rambey, “Simulasi Proses Pemotongan Bubut Baja Karbon Rendah Aisi 1018 dengan Mesin Bubut Menggunakan Metode Elemen Hingga,” J. Tek. ITS, vol. 7, no. 1, pp. 2337–3520.
[14] Jusuf Talaperu*), “PEMOTONGAN LOGAM/ DETAIL PRODUK SECARA EKONOMIS PADA MESIN BUBUT PRODUKSI KONVENSIONAL,” J. Teknol., vol. 8, no. 2, pp. 917–920, 2011.
[15] S. Hestukoro, I. Roza, and D. Morfi Nst, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material on Universal Machine Tool,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[16] JUNAIDI, “Analysis Process of St.37 Steel Material Characteristics with Temperature and Time in Heat Treatment Test using Furnace,” J. UHAMZAH, vol. 08, no. 15, pp. 43–49, 1918.
[17] Junaidi, “Tu 3a Cnc Milling Machine Implementation Using Keller Q Cnc Software Based on Auto Cad 2000 Software,” in Seminar Nasional Teknologi Informasi dan Komunikasi (SNASTIKOM ) HARAPAN, 2017, pp. 349–356.
[18] J. Junaidi, S. Hestukoro, A. Yanie, J. Jumadi, and E. Eddy, “IMPLEMENTATION ANALYSIS of CUTTING TOOL CARBIDE with CAST IRON MATERIAL S45 C on UNIVERSAL LATHE,” in Journal of Physics: Conference Series, 2017, vol. 930, no. 1.
[19] A. Y. junaidi, dharmawati, “Analysis Cutting Tool High Speed Steel ( HSS ) With Cast Iron Material From Universal Lathe,” in IRSTC 2015 PROCEDING, 2015, pp. 464–477.
[20] indra roza junaidi, weriono, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material On Universal Machine Tool,” IJISRT (International J. Innov. Sci. Res. Technol., vol. 3, no. 1, pp. 447–456, 2018.
[21] JUNAIDI, “Analyze cutting tools (HSS) with cast iron material on Universal Lathes,” in Makalah PEKAN ILMIAH Periode XXII-TA.2014/2015 FAKULTAS TEKNIK UISU, 2015, pp. 51–58.
[22] JUNAIDI dan EDDY, “Analysis of Cutting Carbide Tools with S45C Material on Universal Lathes,” in Seminar Nasional FT.UISU, 2017, pp. 116–123.
[23] indra roza junaidi, weriono, “Irrigation Water Debit Analysis that will be used on Micro Power Plant in SEI . Rampah Sub-District of Serdang Bedagai Regency,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[2] S. Hestukoro, T. Siagian, A. Bakhori, and I. Siregar, “Analysis Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[3] S. Hestukoro, T. Siagian, A. Bukhori, I. Roza, and I. Siregar, “Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[4] M. akhi. junaidi, m.idris, “Analisa Pahat Potong HSS Dengan Material Besi Cor Pada Mesin Bubut Universal,” MEDAN, 1, 2015.
[5] Junaidi, “WORKING PROCESS OF TU 3A CNC FRAIS MACHINE USING SOFTWARE SYSTEM.”
[6] A. Yanie, “ANALYSIS CUTTING TOOL HIGH SPEED STEEL (HSS ) WITH CAST IRON MATERIAL FROM UNIVERSAL LATHE.”
[7] J. Junaidi, METROLOGI DAN PENGUKURAN, 1st ed. MEDAN: P4M UNHAR, 2018.
[8] JUNAIDI, ANALISA PERHITUNGAN PAHAT POTONG, 1st ed. MEDAN: Sekolah TinggiTeknik Harapan (STTH) Medan, 2016.
[9] I. M. L. Batan, “Metode Pemeriksaan Mampu Ukur Suatu Rancangan Ditinjau dari Spesifikasi Produk Dengan Bantuan Checklist,” J. Tek. Mesin, Vol. 2, Nomor 1, Januari 2002, vol. 2, no. 1, pp. 1–8, 2002.
[10] Jusuf Talaperu*), “PEMOTONGAN LOGAM/ DETAIL PRODUK SECARA EKONOMIS PADA MESIN BUBUT PRODUKSI KONVENSIONAL,” TEKNOLOGI, vol. 8, no. 2, pp. 917–920, 2011.
[11] B. S. Angga Zeptiawan Sastal1, Yuspian Gunawan2, “PENGARUH KECEPATAN POTONG TERHADAP PERUBAHAN TEMPERATUR PAHAT DAN KEAUSAN PAHAT BUBUT PADA PROSES PEMBUBUTAN BAJA KARBON SEDANG,” ENTHALPY-Jurnal Ilm. Mhs. Tek. Mesin, vol. 3, no. 1, pp. 1–11.
[12] (4) Hernadewita (1) Hendra, (2) Sutarmadi, (3) Anizar Indriani, “JENIS MATERIAL PAHAT POTONG DAN RUN OUT TERHADAP KEKASARAN PERMUKAAN BENDA KERJA SILINDER PADA PROSES BUBUT,” Jenis Mater. Pahat Potong Dan Run Out Terhadap Kekasaran Permukaan Benda Kerja Silinder Pada Proses Bubut, vol. 4, no. 2, pp. 376–385.
[13] M. I. P. H. dan W. J. Mustafid Amna Rambey, “Simulasi Proses Pemotongan Bubut Baja Karbon Rendah Aisi 1018 dengan Mesin Bubut Menggunakan Metode Elemen Hingga,” J. Tek. ITS, vol. 7, no. 1, pp. 2337–3520.
[14] Jusuf Talaperu*), “PEMOTONGAN LOGAM/ DETAIL PRODUK SECARA EKONOMIS PADA MESIN BUBUT PRODUKSI KONVENSIONAL,” J. Teknol., vol. 8, no. 2, pp. 917–920, 2011.
[15] S. Hestukoro, I. Roza, and D. Morfi Nst, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material on Universal Machine Tool,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[16] JUNAIDI, “Analysis Process of St.37 Steel Material Characteristics with Temperature and Time in Heat Treatment Test using Furnace,” J. UHAMZAH, vol. 08, no. 15, pp. 43–49, 1918.
[17] Junaidi, “Tu 3a Cnc Milling Machine Implementation Using Keller Q Cnc Software Based on Auto Cad 2000 Software,” in Seminar Nasional Teknologi Informasi dan Komunikasi (SNASTIKOM ) HARAPAN, 2017, pp. 349–356.
[18] J. Junaidi, S. Hestukoro, A. Yanie, J. Jumadi, and E. Eddy, “IMPLEMENTATION ANALYSIS of CUTTING TOOL CARBIDE with CAST IRON MATERIAL S45 C on UNIVERSAL LATHE,” in Journal of Physics: Conference Series, 2017, vol. 930, no. 1.
[19] A. Y. junaidi, dharmawati, “Analysis Cutting Tool High Speed Steel ( HSS ) With Cast Iron Material From Universal Lathe,” in IRSTC 2015 PROCEDING, 2015, pp. 464–477.
[20] indra roza junaidi, weriono, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material On Universal Machine Tool,” IJISRT (International J. Innov. Sci. Res. Technol., vol. 3, no. 1, pp. 447–456, 2018.
[21] JUNAIDI, “Analyze cutting tools (HSS) with cast iron material on Universal Lathes,” in Makalah PEKAN ILMIAH Periode XXII-TA.2014/2015 FAKULTAS TEKNIK UISU, 2015, pp. 51–58.
[22] JUNAIDI dan EDDY, “Analysis of Cutting Carbide Tools with S45C Material on Universal Lathes,” in Seminar Nasional FT.UISU, 2017, pp. 116–123.
[23] indra roza junaidi, weriono, “Irrigation Water Debit Analysis that will be used on Micro Power Plant in SEI . Rampah Sub-District of Serdang Bedagai Regency,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
Published
2019-06-01
How to Cite
[1]
T. Sutoyo, “PENGARUH VARIASI KUAT ARUS LAS LISTRIK PADA PENGELASAN BAJA C45 DENGAN SUDUT KAMPU V GANDA TERHADAP UJI TARIK DAN UJI IMPAK”, Jurnal Simetri Rekayasa, vol. 1, no. 1, pp. 25-35, Jun. 2019.
Section
Articles
