ANALISIS KARAKTERISTIK HASIL PROSES PENGECORAN BESI COR KELABU DENGAN VARIASI DESIGN MODEL INTI COR
Keywords:
Characteristics, green sand mold, bentonite, gray cast iron, physical and mechanical
Abstract
This study is a study that mengililasi casting process gray cast iron. From the characteristics obtained data table attached. Based on the results of research that the microstructure of the specimens in this study is the result of casting gray cast iron which has a strong and sturdy perlite metric. Graphite flakes in specimens I (3% Bentonite) were harder than specimens II (5% Bentonite). Ferrite in specimen I was more than ferrite in specimen II. Specimen I has a rather rough pearlite structure, while specimen II has fine pearlite. The hardness of gray cast iron possessed by 66.5 HRA II specimens was higher than that of gray cast iron possessed by specimen I which was 55.8 HRA. The tensile strength in specimens II was 278.68 N / mm2 higher than the tensile strength of specimens I was 222.92 N / mm2
Downloads
Download data is not yet available.
References
[1] PRABA APRILIYANTO, “ANALISIS VARIABEL PROSES PRODUK PENGECORAN LOGAM MENGGUNAKAN CETAKAN SAND CASTING,” JTM., vol. 2, no. 2, pp. 70–78, 2014.
[2] A. S. S. J. M.Bayu Prakoso1, Doli Tryono Siregar2, “ANALISA BRAKE SHOE MOBIL AVANZA VELOZ 1,5 TOYOTA AKIBAT SISTEM PENGEREMAN,” Int. J. Logist., vol. 1, no. 3, pp. 1–6, 2018.
[3] H. L. Junaidi1, Eddi koto2, Nismah Panjaitan 3, “ANALYSIS OF MICRO STRUCTURE AND LAS DISABILITY IN THE PRODUCTION PROCESS OF TRAIN BOGIE FRAMEWORK,” TEKNOLOGI, vol. 19, no. 2, pp. 1–9, 2019.
[4] S. B. B. H. Y. Estriyanto, “PERBANDINGAN KUALITAS HASIL PENGECORAN PASIR CETAK BASAH DENGAN CAMPURAN BENTONIT 3% DAN 5% PADA BESI COR KELABU,” Prodi. Pend. Tek. Mesin, Jur. Pendidik. Tek. dan Kejuruan. FKIP, UNS, pp. 1–8, 2013.
[5] S. Hestukoro, T. Siagian, A. Bakhori, and I. Siregar, “Analysis Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[6] B. T. S. Junaidi1, Angri Abdirullah2, “ANALISA KARAKTERISTIK SERAT KNAF DENGAN PEMBEBANAN IMPACT UNTUK RANCANGAN DENGAN SPESIFIKASI UKURAN 80/20,70/30.60/40,50/50,40/60,” TEKNOLOGI, vol. 1, no. 3, pp. 1–9, 2019.
[7] J. Ahmad Nur Ikshan1, Ismi Juwanisa2, Taufik Sutoyo3, “ANALISIS HASIL PEMERIKSAAN HEATTREAMENT PADA PENGECORAN BAJA ST 37 DENGAN MEDIA PENDINGIN AIR DAN OLI SAE 40,” TEKNOLOGI, pp. 1–9, 2018.
[8] Junaidi, “WORKING PROCESS OF TU 3A CNC FRAIS MACHINE USING SOFTWARE SYSTEM.”
[9] A. Yanie, “ANALYSIS CUTTING TOOL HIGH SPEED STEEL (HSS ) WITH CAST IRON MATERIAL FROM UNIVERSAL LATHE.”
[10] B. T. S. Junaidi1, Angri Abdirullah2, “CHARACTERISTIC ANALYSIS OF KNAF FIBER WITH IMPACT LOADING FOR DESIGN WITH SPECIFICATIONS SIZE 80 / 20.70 / 30.60 / 40.50 / 50.40 / 60,” STASTIKA, vol. 1, no. 1, p. 2019, 2019.
[11] B. T. S. FAHRIZA TRI RIZKI1, ANGGRI ABDIRULLAH2, “ANALISA KEKUATAN PEMBUBUTAN MATERIAL S45C MENGGUNAKAN PAHAT CARBIDE,” TEKNOLOGI, pp. 1–9, 2018.
[12] T. Siagian, I. Siregar, and H. Lubis, “Characteristics of St.37 Steel Materials with Temperature and Time on Heat Treatment Test using Furnace,” 2018.
[13] F. A. A. T. MUHAMMAD IQBAL PASARIBU1, GUSTAMA PUTRA ALHADI2 and JUNAIDI4, “MERANCANG ROBOT PENGANGKAT BARANG MENGGUNAKAN ALIRAN KONDENSOR TIPE SHEEL DAN TUBE YANG DI OPTIMALKAN ENERGI MATERIAL TWISTLOCK,” TEKNOLOGI, pp. 1–11, 2018.
[14] J. Taufik Sutoyo1, M.Yunus Azmi2 , Eli Hamonangan.G3, “PENGARUH GAYA POTONG PADA PROSES PEMBUBUTAN TERHADAP MATERIAL DENGAN PAHAT CARBIDE,” TEKNOLOGI, pp. 1–13, 2018.
[15] A. S. Ahmar et al., “Lecturers’ understanding on indexing databases of SINTA, DOAJ, Google Scholar, SCOPUS, and Web of Science: A study of Indonesians,” in Journal of Physics: Conference Series, 2018.
[16] S. Hestukoro, I. Roza, and D. Morfi Nst, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material on Universal Machine Tool,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[17] D. J. M.RINOZA1, M AGUNG PRATAMA2, “STUDI KASUS AUDIT MAINTENANCE MESIN PEMINDAH BAHAN MATERIAL HANDLING DIPABRIK TEKSTIL,” TEKNOLOGI, pp. 1–5, 2018.
[18] D. J. M.RINOZA1, M AGUNG PRATAMA2, “STUDI KASUS AUDIT MAINTENANCE MESIN PEMINDAH BAHAN MATERIAL HANDLING DIPABRIK TEKSTIL,” J. Teknol., pp. 1–4, 2018.
[19] J. Junaidi, S. Hestukoro, A. Yanie, J. Jumadi, and E. Eddy, “IMPLEMENTATION ANALYSIS of CUTTING TOOL CARBIDE with CAST IRON MATERIAL S45 C on UNIVERSAL LATHE,” in Journal of Physics: Conference Series, 2017, vol. 930, no. 1.
[20] J. Mhd furqan maulana1 , ichwanul siddiq2, Anan nawawi siregar3, “ANALISA SISTEM KOPLING PADA MOBIL TOYOTA AVANZA,” TEKNOLOGI, pp. 1–7, 2018.
[21] J. Junaidi, METROLOGI DAN PENGUKURAN, 1st ed. MEDAN: P4M UNHAR, 2018.
[22] indra roza junaidi, weriono, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material On Universal Machine Tool,” IJISRT (International J. Innov. Sci. Res. Technol., vol. 3, no. 1, pp. 447–456, 2018.
[23] indra roza junaidi, weriono, “Irrigation Water Debit Analysis that will be used on Micro Power Plant in SEI . Rampah Sub-District of Serdang Bedagai Regency,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[24] H. K. JUNAIDI1 , TONY SIAGIAN2 , Anggri Abdirullah3 , Aji Surahman 4, “CALCULATION ANALYSIS OF CUTTING STYLE IN MIXING PROCESS TOWARDS MATERIALS WITH SPEED CARBIDE USING CHARACTERISTICS,” TEKNOLOGI, vol. 19, no. 1, pp. 1–19, 2019.
[2] A. S. S. J. M.Bayu Prakoso1, Doli Tryono Siregar2, “ANALISA BRAKE SHOE MOBIL AVANZA VELOZ 1,5 TOYOTA AKIBAT SISTEM PENGEREMAN,” Int. J. Logist., vol. 1, no. 3, pp. 1–6, 2018.
[3] H. L. Junaidi1, Eddi koto2, Nismah Panjaitan 3, “ANALYSIS OF MICRO STRUCTURE AND LAS DISABILITY IN THE PRODUCTION PROCESS OF TRAIN BOGIE FRAMEWORK,” TEKNOLOGI, vol. 19, no. 2, pp. 1–9, 2019.
[4] S. B. B. H. Y. Estriyanto, “PERBANDINGAN KUALITAS HASIL PENGECORAN PASIR CETAK BASAH DENGAN CAMPURAN BENTONIT 3% DAN 5% PADA BESI COR KELABU,” Prodi. Pend. Tek. Mesin, Jur. Pendidik. Tek. dan Kejuruan. FKIP, UNS, pp. 1–8, 2013.
[5] S. Hestukoro, T. Siagian, A. Bakhori, and I. Siregar, “Analysis Characteristics of Silicon Aluminum Material Based on Fracture Period In Torque Test.”
[6] B. T. S. Junaidi1, Angri Abdirullah2, “ANALISA KARAKTERISTIK SERAT KNAF DENGAN PEMBEBANAN IMPACT UNTUK RANCANGAN DENGAN SPESIFIKASI UKURAN 80/20,70/30.60/40,50/50,40/60,” TEKNOLOGI, vol. 1, no. 3, pp. 1–9, 2019.
[7] J. Ahmad Nur Ikshan1, Ismi Juwanisa2, Taufik Sutoyo3, “ANALISIS HASIL PEMERIKSAAN HEATTREAMENT PADA PENGECORAN BAJA ST 37 DENGAN MEDIA PENDINGIN AIR DAN OLI SAE 40,” TEKNOLOGI, pp. 1–9, 2018.
[8] Junaidi, “WORKING PROCESS OF TU 3A CNC FRAIS MACHINE USING SOFTWARE SYSTEM.”
[9] A. Yanie, “ANALYSIS CUTTING TOOL HIGH SPEED STEEL (HSS ) WITH CAST IRON MATERIAL FROM UNIVERSAL LATHE.”
[10] B. T. S. Junaidi1, Angri Abdirullah2, “CHARACTERISTIC ANALYSIS OF KNAF FIBER WITH IMPACT LOADING FOR DESIGN WITH SPECIFICATIONS SIZE 80 / 20.70 / 30.60 / 40.50 / 50.40 / 60,” STASTIKA, vol. 1, no. 1, p. 2019, 2019.
[11] B. T. S. FAHRIZA TRI RIZKI1, ANGGRI ABDIRULLAH2, “ANALISA KEKUATAN PEMBUBUTAN MATERIAL S45C MENGGUNAKAN PAHAT CARBIDE,” TEKNOLOGI, pp. 1–9, 2018.
[12] T. Siagian, I. Siregar, and H. Lubis, “Characteristics of St.37 Steel Materials with Temperature and Time on Heat Treatment Test using Furnace,” 2018.
[13] F. A. A. T. MUHAMMAD IQBAL PASARIBU1, GUSTAMA PUTRA ALHADI2 and JUNAIDI4, “MERANCANG ROBOT PENGANGKAT BARANG MENGGUNAKAN ALIRAN KONDENSOR TIPE SHEEL DAN TUBE YANG DI OPTIMALKAN ENERGI MATERIAL TWISTLOCK,” TEKNOLOGI, pp. 1–11, 2018.
[14] J. Taufik Sutoyo1, M.Yunus Azmi2 , Eli Hamonangan.G3, “PENGARUH GAYA POTONG PADA PROSES PEMBUBUTAN TERHADAP MATERIAL DENGAN PAHAT CARBIDE,” TEKNOLOGI, pp. 1–13, 2018.
[15] A. S. Ahmar et al., “Lecturers’ understanding on indexing databases of SINTA, DOAJ, Google Scholar, SCOPUS, and Web of Science: A study of Indonesians,” in Journal of Physics: Conference Series, 2018.
[16] S. Hestukoro, I. Roza, and D. Morfi Nst, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material on Universal Machine Tool,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[17] D. J. M.RINOZA1, M AGUNG PRATAMA2, “STUDI KASUS AUDIT MAINTENANCE MESIN PEMINDAH BAHAN MATERIAL HANDLING DIPABRIK TEKSTIL,” TEKNOLOGI, pp. 1–5, 2018.
[18] D. J. M.RINOZA1, M AGUNG PRATAMA2, “STUDI KASUS AUDIT MAINTENANCE MESIN PEMINDAH BAHAN MATERIAL HANDLING DIPABRIK TEKSTIL,” J. Teknol., pp. 1–4, 2018.
[19] J. Junaidi, S. Hestukoro, A. Yanie, J. Jumadi, and E. Eddy, “IMPLEMENTATION ANALYSIS of CUTTING TOOL CARBIDE with CAST IRON MATERIAL S45 C on UNIVERSAL LATHE,” in Journal of Physics: Conference Series, 2017, vol. 930, no. 1.
[20] J. Mhd furqan maulana1 , ichwanul siddiq2, Anan nawawi siregar3, “ANALISA SISTEM KOPLING PADA MOBIL TOYOTA AVANZA,” TEKNOLOGI, pp. 1–7, 2018.
[21] J. Junaidi, METROLOGI DAN PENGUKURAN, 1st ed. MEDAN: P4M UNHAR, 2018.
[22] indra roza junaidi, weriono, “Process Analysis of High Speed Steel Cutting Calculation (HSS) with S45 C Material On Universal Machine Tool,” IJISRT (International J. Innov. Sci. Res. Technol., vol. 3, no. 1, pp. 447–456, 2018.
[23] indra roza junaidi, weriono, “Irrigation Water Debit Analysis that will be used on Micro Power Plant in SEI . Rampah Sub-District of Serdang Bedagai Regency,” Int. J. Innov. Sci. Res. Technol., vol. 3, no. 1, 2018.
[24] H. K. JUNAIDI1 , TONY SIAGIAN2 , Anggri Abdirullah3 , Aji Surahman 4, “CALCULATION ANALYSIS OF CUTTING STYLE IN MIXING PROCESS TOWARDS MATERIALS WITH SPEED CARBIDE USING CHARACTERISTICS,” TEKNOLOGI, vol. 19, no. 1, pp. 1–19, 2019.
Published
2019-06-01
How to Cite
[1]
S. Candra, “ANALISIS KARAKTERISTIK HASIL PROSES PENGECORAN BESI COR KELABU DENGAN VARIASI DESIGN MODEL INTI COR”, Jurnal Simetri Rekayasa, vol. 1, no. 1, pp. 18-24, Jun. 2019.
Section
Articles
